The mold of each part is also color-coded according to the balance with the internal parts. Although it is slender, it is mechanically made, such as the armor of each part is divided into small parts. I’m a little worried that there will be seams on the sides of the internal frame. The three pieces of armor are also color-coded by parts and can be deployed and stored. The shoulder armor is also mechanically made with a mold. The sensor is color-coded with a green sticker on the clear parts. The red wing on the side can also be stored. However, please note that it will not deploy if the forearm is rolled. Only the thumb is movable for the hand parts, and the remaining 4 fingers are recombinable.īy sliding the armor of the forearm, the joint part for stably holding the twin buster rifle is exposed. Both the white and blue armor of the forearm are sandwiched between the left and right, but the seams are molded by stepping down. The upper arm is tubular and has no seams. There is no big change in the form here either, but the mold is finely shaped, and the shoulder armor and forearm armor are also realistically color-coded by parts. Every detail is carefully made.Ĭompare the arms side by side with the MG version. The back of the waist armor has backing parts for each part. The crotch part slides back and forth to increase the range of motion of the legs. The side armor can be widely deployed by the arm, like the neo-bird form deformation. The range of motion of the arm is expanded, and you can reproduce a more natural pose with a twin buster rifle held in both hands. The cockpit hatch can be opened and closed toward you. The machine cannon can be pulled out to the front, or it can be turned to the top. Unfolding exposes the internal machine cannon. The armor on the shoulder can be opened and closed. The search eye is a specification that puts a green sticker and covers it with dome-shaped clear parts. Since the left and right armor are composed of exterior parts, the internal frame is simple. Including the rear armor, the feeling of modeling density is different compared to the MG version.Ĭhest internal frame. It has a fairly detailed parts composition, and the armor of the air intake and the antenna of the chest plate are also color-coded with separate parts.

It is made with sharpness such as being finely color-coded with separate parts. The side wings can be deployed for the Zero system. The sensors on the front and back of the twin eyes and combs are color-coded with stickers attached to the clear parts. The mat part is a left and right sandwich type, but the seam of the back of the head is stepped down and molded. At first glance, there is not much difference, but the impression is that the mold of each part is deep and sophisticated. Let’s take a look at each part while comparing it with MG Wing Gundam Zero EW (MG Wing Gundam Zero EW & Special Coating, hereafter, MG version released from P-Bandai.Ĭompare the head with the MG version. There is no special emblem, but many caution type markings are included. Shield, twin buster rifle, beam saber blade ☓2, joint parts for atmospheric entry mode, joint parts for neo-bird form, 2 types of joint parts for display, finger parts (for flat hands: left and right, for weapon holders: left and right, for grip hands: Left and right), figures are included.Ĭomes with a dark gray molded color slide lock action base. Since it is equipped with a wing peculiar to the back, specific gravity is applied to the rear, but if the wings are arranged in a well-balanced manner, it is possible to stand on its own. ABS is used where strength is required, and KPS is used for joints and internal parts. Undergates are used for parts such as the exterior of each part and the back wing to make the gate marks as inconspicuous as possible. There is almost no need for painting, and the finish is sufficient with bare assembly. The seal only supplements the sensor of each part. The interior and joint parts are grouped in gray molding color. The molding colors are mainly two metallic blue colors and a clean matte white, and some red and yellow colors are used. By thoroughly verifying the joint mechanism and deformation mechanism, it is a kit that realizes an expansion of the range of motion and smooth deformation to the neobird form. Reproduce the characteristic body shape with biological wings with completely new modeling. Hajime Katoki of MS “Wing Gundam Zero” that appears in “New Mobile Report Gundam W Endless Waltz”. MG Wing Gundam Zero EW Ver.Ka is a 1/100 scale model kit completely supervised by Mr. MG Wing Gundam Zero EW Ver.Ka review and comparison

Perfect grade wing zero review